|
Product Overview |
Room Settings |
Design Option |
Size Standard |
Warranty
Design Option
|
|
Pretensioned Skylight: Model ST2W
The ST2W was designed for inside mounting only for both horizontal and slanted installations. It can be tilted, but not raised. The blind has a headrail at each end and the slats are supported by factory pre-set tension wires. The maximum width is 48", maximum length 72", and a minimum length 12". Comes standard with tilt knob on left side of higher headrail. Specify detachable wand length when ordering - 30", 60" or 84". Requires special installation brackets (provided).
Note: For proper operation, tension for support of skylight blinds shall be in steel cables and not in string tapes of blind.
|
^ top
|
|
Inclined: Model SB45
This inclined blind has both tilt and lift capabilities when the incline, or slope, does not exceed 45° from the vertical.
The blind is supported by turnbuckle tensioned wires and requires special hardware (provided) for inside mounting only. For outside mounting, additional hardware may be required. Maximum width is 115", maximum height 100". Minimum width 18", minimum height 12". Comes standard with wand tilt on left, cord lock on right, and right pull on a short cord.
|
^ top
|
|
Turnbuckle Skylight: Model TBSL
For use in large skylight applications, the TBSL can be mounted inside or outside the skylight opening at any angle. It can be tilted but not raised, and has a maximum width of 115", maximum height 100". For sizes below 48"w x 72"h, model ST2W is recommended. The TBSL has a headrail at each end and is supported by turnbuckle tensioned wires. The TBSL comes with a wand tilter on the left side of the higher headrail. A valance is provided as standard. Requires special installation hardware (provided).
|
^ top
|
|
A-Frame: Model SDAF
For A-frame windows with maximum widths and heights to 100", down to minimum width of 19" and a minimum height of 12". The A-frame blind will tilt and lift to the lowest point of the headrail (A). The slats will "fan" at the highest point to assure privacy. The SDAF can be mounted inside or outside the casing, and comes with wand tilt left and cord tilt lift on the right side of the headrail. Provide accurate dimensions for B, C and D. (Max. angle: C must be greater than D-B) Template required.
|
^ top
|
|
Inverted A-frame: Model SDIA
For inverted A-frame windows with maximum size of 100" for A or D, minimum sizes of 12" for D and 19" for A. The inverted A-frame blind will tilt, but will only lift to the high point of C. Standard controls, wand tilt left, cord tilt right. The SDIA can be mounted wither inside or outside the casing. Provide accurate dimensions for A, B and D, Template required.
Note: Slats will fan at lowest corner for privacy.
|
^ top
|
|
Right Angle Triangle: Model SDRT
For windows that have a maximum size of 72" or a minimum size of 24" for B or C. The model SDRT must be constructed so dimension B is equal to or longer than C. The headrail (A) valance supplied is standard and requires final trimming after installation to conform to top and bottom angles. The blind can be tilted, but not raised. Wand tilt is located at high side of headrail (A) The SDRT can be mounted inside or outside the casing. Provide accurate dimensions for B and C. Template required.
|
^ top
|
|
Inverted Taper: Model SDIT
The inverted taper can be tilted, but in most cases not raised. When the difference between the headrail length and bottom rail length exceeds 9", or the taper exceeds 9", the blind must be an inside mount. Size limits are the same as those for model SDTA. Wand tilt is provided standard on the left side of the headrail. Provide accurate dimensions for A, B, C and D. Template required.
|
^ top
|
|
Taper: Model SDTA
A tapered blind can be tilted and raised provided the taper does not exceed 9". If the taper is greater than 9", the blind will tilt only, and can be installed as a inside mount. The maximum width is 100", maximum height 100", minimum width 24", minimum height 12". Standards include want tilt on left, and cord tilt on right of headrail. Provide accurate dimensions for A, D and C. Template required.
|
^ top
|
|
Double Taper: Model SDDT
The double taper blind can be tilted, but in most cases not raised. When the difference between the headrail length and bottom rail length exceeds 9" the blind must be an inside mount. Size limits are the same as those for model SDTA. Wand tilt is provided standard on the left side of the headrail. Provide accurate dimensions for A, B, C, D and E. Template required.
|
^ top
|
|
Arch: Model SDAR
For small arch windows where the maximum length (C) is 60", with a minimum length of 9" for C minus B. The maximum width (A) is 90", with a minimum width of 18". The blind will tilt but cannot be raised.
Note: If the C dimension exceeds 60" or if lift capabilities are desired, refer to model SDAH (combined arch and horizontal blind). The SDAR uses a bottom mounted headrail, with auxiliary tape supports attached inside the window frame for mounting. Can be inside mounted only with supplied hardware. Wand tilt provided on left side of headrail. Template required.
|
^ top
|
|
Isosceles Triangle: Model SDIS
For windows of this configuration with a maximum size of 72", or a minimum size of 24" for lengths A, B or C. The model SDIS must be constructed so dimension D will be approximately 8" wide. The peak of the triangle will not be covered by slats, and the blind cannot be raised, but can be tilted. The headrail is located at the bottom of the blind with auxiliary tape supports attached to the inside of the window frame. The blind can only be inside mounted, and the wand tilt is located at the left of the headrail. Template required.
|
^ top
|
|
Combined Arch and Horizontal: Model SDAH
This application involves two blinds, an arch at the top and a horizontal blind at the bottom. The installed unit will have two headrails where the arch and the rectangular sections meet. The maximum length of A is 90" with an overall length B of 180". The minimum B minus A length is 9". The maximum width C is 60" unless there is a possibility of mounting an intermediate support bracket at the arch and horizontal headrails. The minimum width C is 18". The arch section will have wand tilt on the left side of the headrail, but no lift capabilities. The rectangular section will have normal lift and tilt functions, and standard control locations. Template required for arch section.
|
^ top
|
|
Circular or Oval: Model SDCO
This type of blind is constructed using two horizontal headrails at the center of the blind. It is basically a combination of two arch blinds, an upper and lower with auxiliary cable tape supports used at each tape position. The maximum diameter is 90" with a minimum diameter of 18". It can be tilted, but not raised. Controls for upper and lower sections are located on the left side of the headrail. Template required.
|
^ top
|
